View and Download Canon DRC service manual online. DRC Scanner pdf manual download. Also for: Dr free pdf instructions. Find the office and computer equipment manual you need at ManualsOnline. Canon DRC Scanner User Manual. Page 1. Page 2. Chapter 5. Other Functions. Setting in the User Mode. You can select the mode of operation (user mode) for the scanner from those listed below. ○ Operation.
|Published (Last):||27 August 2013|
|PDF File Size:||17.97 Mb|
|ePub File Size:||9.60 Mb|
|Price:||Free* [*Free Regsitration Required]|
Page Chapter 7 Daily Cleaning This chapter describes daily cleaning of the scanner. Ask a Question Usually answered in minutes! U Use the imprinter in the Count Only mode. Page Clean the inside of the machine as necessary. I Do not turn OFF the canoon or remove any interface cables when an application is running. If this mode is executed with no document loaded, an error window See Fig.
Setting in the user mode – Canon DR-9080C User Manual
Lift up the stopper. After that, the pick-up motor and feed motor are started simultaneously to feed the document. Page Cable Manal Fig. Page Note 2: Posted on Aug 20, Be the first to answer.
Parts Request, the full item description, the item part number and the quantity. Page Index Index – A – Document tray extension.
Chapter 7 Daily Cleaning Use a clean, soft cloth to wipe the scanning glasses. There is manuwl driver for the OS Version you selected. Power Cord A cotton-tipped swab is also acceptable.
After you finish reading this manual, store it in a safe place for future reference. Check the operation of the pick-up sensor.
U Sound buzzer during key operation default. Page Reading unit Is the problem solved when the End. U Use the endorser in the A4 mode.
Never spray mild detergent or water directly on the scanning glasses. Page 57 In this case, the brightness and contrast adjustments become invalid. Installing The Software 3.
imageFORMULA DRC Color Production Scanner
Page 76 Reading the back side of documents. Install the endorser cable assembly with two stepped screws. Chapter 7 Daily Cleaning Lock the manuak.
Order them both, they are pretty cheap. Turns document run into the registration roller so that Document this way the skew is corrected. Adjust the position of the stopper to match the length of the document.
Be sure to open and read the Readme. Chapter 7 Daily Cleaning Move the retard rollers to the left and remove 9080x. Detach the upper unit while holding it to prevent it from falling.
Pull the lever that locks the feed rollers in place towards you. Error code Cause Number of document sheets to be scanned exceeds set number of sheets in the verify scan. Do not use the imprinter in the Count Only mode default. In this case, the brightness and contrast adjustments become invalid. G The displayed dialog box differs depending on which Windows operating system Note you are using. Check to see if the document was scanned correctly, and scan the document again.
The gear wheel and the paper guide must be placed correctly so that it moves freely.
Canon Scanner DRC User Guide |
Do not detect double feed in the Count Only mode default. Answered on Jun 01, Align a batch of documents to be scanned until the edges are even. If you turn tray upside down, you will notice screws, remove them carefully.
The buzzing noise from the lift tray may or may not be related.
Popular Tags error reset paper jam line clean c01 tray calibration install driver black line scan feed tray image stop scanning memory not found. Do not block the air vent, otherwise the temperature will rise inside the machine and a fire might result. Then the scanner assumes the cover is closed. Detect double feed in the Count Only mode. Chapter 2 Preparation Before Use This chapter describes the procedure from scanner connection through to turning ON the power.
Install the upper delivery cover assembly. Low level accuracy staple detection. Page Chapter 7 Daily Cleaning Lock the lever. Chapter 5 Other Functions Document Detection Function The scanner is equipped with a document detection function which stops a document from feeding if it detects that the document is not being fed correctly. Place the document face up in the document tray, aligning the document’s top edge against the back of the document tray.
Page 1 and the feed guide plate 2.