HYPERTHERM HPR260XD MANUAL PDF

Hypertherm, HyPerformance, HyDefinition, LongLife and CommandTHC are trademarks of .. HPRXD Manual Gas – Revision 2. guarantees the Hypertherm quality you can count on. The HPRXD delivers superior bar ( psi) Manual gas console. 8 bar ( psi). ArcGlide, EDGE Pro, Hypertherm, HPR and Sensor THC are trademarks of Hypertherm, Inc. and may be When you see a safety symbol in this manual or on your machine HPRXD, HPRXD with a built-in.

Author: Malalabar Fenrikazahn
Country: Mayotte
Language: English (Spanish)
Genre: Music
Published (Last): 23 September 2017
Pages: 416
PDF File Size: 19.31 Mb
ePub File Size: 13.16 Mb
ISBN: 536-8-58200-676-3
Downloads: 39965
Price: Free* [*Free Regsitration Required]
Uploader: Milabar

The valve assembly should also have a separate ground connection to the gantry bus bar. Isolate the electrical equipment and disconnect all live conductors from the supply voltage when in the OFF position Have manuap OFF and one ON position clearly marked with O OFF and l ON Have an external operating handle capable of being locked in the OFF position Contain a power-operated mechanism that serves as an emergency stop Have slow-blow fuses installed for the proper breaking capacity see table above.

Torch alignment To align the torch at right angles to the workpiece, use a square.

This cutting equipment is designed for use only in an industrial environment. No corte cerca de sustancias inflamables. The hypetrherm cutting capability edge start is 64 mm 2. Size, air volume, ventilation and filtration of the work area.

Hypertherm HPRXD Manual Gas Rev.3 manuals

Turn OFF the power to the system. Laser safety training may be required. No levante la pieza a cortar ni los residuos de corte durante la tarea. Earthing of the workpiece Where the workpiece is not bonded to earth for electrical safety, nor connected to earth because of its size and position, for example, ship s hull or building steel work, a connection bonding the workpiece to earth may reduce emissions in some, but not all instances.

Failure to do so can result in death or electrical. Remove Mounting Base 3.

  ISINGS ROMAN GLASS FROM DATED FINDS PDF

HyPerformance Plasma. HPRXD Manual gas. Instruction manual Revision 2 – PDF

The connectors in steps 7 0 are push-to-connect fittings. Noise can damage hearing Cutting with a plasma arc can exceed acceptable noise levels as defined by hpr260xr codes in many applications. While is flowing adjust the supply regulator for the plasma to 8 bar 5 psi.

Do not inhale fumes. The air quality level in any relevant workplace depends on site-specific variables such as: Reproduction is forbidden unless authorized. Arun, Hypertherm have a PDF download on improving hole cut quality. Within thirty 30 days before any such transfer occurs, you agree to notify in writing Hypertherm, which reserves the right of approval.

Install the torch with torch leads attached in the torch mounting bracket. I look forward to receiving two signed copies of this letter. The forks must also be centered front to back and side to side to prevent tipping while moving. Use ear protectors if the noise is disruptive or if there is a risk of hearing damage after all other engineering and administrative controls have been implemented.

Specific information by product can be found in the Hypertherm downloads library at: Installation must be performed by a licensed electrician. For example, the spark gaps of arc striking and stabilizing devices should be adjusted and maintained according to the manufacturer s recommendations. Introduction This document describes the grounding and shielding necessary to protect a plasma cutting system installation against radio frequency interference RFI and electromagnetic interference EMI noise.

Never run the shield or the drain through the connector on any of the pins. December 10, File number: It prevents a shock hazard to any personnel from any of the equipment, or the work table.

Do not alter the length of the hoses. It is not subject. Computer and other control equipment. The CNC cable must be constructed using cable with degree shielding and metal housing connectors at each end. Keep as far away from the power supply as possible.

Please keep these instructions for future reference. The metal braided shield on the torch leads must be connected fi rmly to the ignition console and to the torch. Never operate the plasma system unless the power supply covers are in place.

  DUALPHONE 3088 PDF

HyPerformance Plasma. HPR260XD Manual gas. Instruction manual Revision 2

Hypretherm that those using welding or cutting equipment, as well as air-supplied bypertherm devices, are qualified and trained in the proper use of such equipment. Use a motor-start circuit breaker or equivalent if time delay high inrush fuses are not permitted by local and national codes.

The cutting equipment should not be modified in any way, except as set forth in and in accordance with the manufacturer s written hyperthwrm. Equipment used for calibration or measurement. Consulter le manuel avant de faire fonctionner. Select the product you are looking for from the Product Type drop down menu, choose Regulatory from the Category drop down menu, and choose Acoustical Noise Data Sheets from the Sub Category drop down menu.

The console also houses a relay PC board and a control PC board. Nous vous recommandons de lire attentivement le manuel avant toute utilisation. In no event shall Hypertherm be liable for injury to persons or property damage by reason of any code violation or poor work practices.

Utiliser des affiches ou des panneaux. Use a high-quality, 2-stage, regulator to maintain consistent supply pressure from high pressure cylinders. Insurance At all times you will have and maintain insurance in such quantities and types, and with coverage sufficient and appropriate to defend and to hold Hypertherm harmless in the event of any cause of action arising from the use of the products. Assessment of area Before installing npr260xd equipment, the user shall make an assessment of potential electromagnetic problems in the surrounding area.

Technical Inspection Services Origine: Keep a fire extinguisher nearby.